網絡上的參考有限，僅有的一個thermal-engine的一篇博客也不是最新的，參考的這篇博客再加上最新的msm8953平臺的thermal-engine，對thermal-engine的配置、算法、加載進行介紹。

代碼位置vendor/qcom/proprietary/thermal-engine/

默認配置文件thermal-engine.conf，里面目前用到的thermal控制算法monitor、ss、virtual。

1.base format:

Strings	說明
{debug}	可選，若有此選項表示使能調試信息
sampling	默認采樣率，以ms為單位
[<Algorithminstance label>]	算法實例標簽
algo_type	算法類型，必須是算法實例的第一個字段
disable	可選，用于默認情況下禁止該算法實例起作用

2.算法類型

inc/thermal_config.h enumalgo_type { UNKNOWN_ALGO_TYPE= -1, MONITOR_ALGO_TYPE= 0, PID_ALGO_TYPE, SS_ALGO_TYPE, TB_ALGO_TYPE, EQUILIBRIUM_TYPE, VIRTUAL_SENSOR_TYPE, BWLM_ALGO_TYPE, ALGO_IDX_MAX, };

■monitor

如果溫度達到thresholds，觸發響應的動作(限制)，當溫度低于thresholds_clr，結束動作(限制)

Strings	說明
algo_type	monitor
sensor	傳感器名稱
sampling	采樣率ms
descending	可選，默認門限是升序，有此字段后門限順序?yàn)榻敌?/span>
thresholds	門限值 mCor mA
thresholds_clr	清除門限值
actions	達到門限時的動作，多個動作時用'+'連接
action_info	動作額外信息，多個額外信息間用'+'連接

■ pid

ProportionalIntegralDerivative，比例-積分-微分控制，當溫度超過最大允許值時，CPU需要降頻，并且使用pid算法將溫度控制在set_point，該控制器輸出的結果可以被轉換成最大允許CPU頻率。

pid簡易的解釋，操作人員控制電加熱爐的爐溫，爐溫會設定一個set_point(需要維持的溫度)，并且顯示當前的溫度，操作人員根據觀察后，通過旋轉電位器的轉角，來控制電流的大小，進一步來控制溫度。增加或者減小電流的比例，與P值相關；這個比例的誤差，與I值相關；變化速率和未來趨勢與D值相關。

Strings	說明
algo_type	pid
sampling	采樣率ms
sensor	傳感器名稱
device	被PID算法調整的設備
set_point	PID算法調整的目標值mCor mA
set_point_clr	PID算法停止調整的值
p_const	PID算法中的P常量
i_const	PID算法中的I常量
d_const	PID算法中的D常量
i_samples	積分組件報錯的積分樣本數
dev_units_per_calc	Unitsof device adjustment per PID calculation outcome 每一個PID算法輸出調整設備單元值
freq_scale	Frequencyscaling factor for DUAL PID

■ ss

DTM策略，即DynamicThermalManagement，動態控制算法有兩個模式，DTM(用于頻率控制)和PID(用于溫度保持)。PID上文已經描述，DTM是基于溫度setpoint，提升或這降低CPU的最大允許頻率。每一個最大允許頻率的調解是基于DCVSfrequency table中的可用頻率steps。溫度高于setpoint時，最大允許頻率會按step逐漸下降，溫度高于setpoint時，最大允許頻率會按step逐漸上升。該策略可以用于控制GPU頻率。

Strings	說明
algo_type	ss
sampling	采樣率ms
sensor	傳感器名稱
device	被PID算法調整的設備
set_point	PID算法調整的目標值mCor mA
set_point_clr	PID算法停止調整的值
time_constant	Multiplierof sampling period for holding off adjustments whencurrent and last error sample are equivalent
device_max_limit	可選，fieldto specify device performance mitgation Ifit is defined, this instance mitigates device up todevice_max_limit value. Itexpects value in KHz for cpu device and Hz for gpu device
device_perf_floor	可選，fieldto specify device performance mitgation floor. Ifit is defined, this instance stops mitigating a device to a levelwith a corresponding perf_lvl at or above device_perf_floor.

■ tb

8998最新支持的算法TokenBucket算法。頻率輸出通過反饋進行控制，類似PID算法概念。當溫度高于set_point的時候，頻率降幅相對較大，然后通過頻率限制，進行溫控維持。

Strings	說明
algo_type	ss
sampling	采樣率ms
sensor	傳感器名稱
device	被PID算法調整的設備
set_point	PID算法調整的目標值mCor mA
set_point_clr	PID算法停止調整的值
time_constant	Multiplierof sampling period for holding off adjustments whencurrent and last error sample are equivalent
up_loop_gain	tokenbucket reward calculations的增益乘法器
down_loop_gain	tokenbucket penalty calculations的增益乘法器
auto_penalty	高于set_point時，增加的額外penalty。 Shouldbe in units of temperature/temp_scale_factor
auto_reward	低于set_point時，增加的額外reward。 Shouldbe in units of temperature/temp_scale_factor
temp_scale_factor	溫度級別劃分因子。Dividerfor temperature to get it to units of Degree Celsius from thevalue returned by reading the sensor.
freq_scale_factor	頻率級別劃分因子。Multiplierfor device frequency readings. Default device frequency unit isKHz, so set to 1 if device frequency is read in KHz, 1000 for Hz.This is necessary because GPU freq is often in Hz.
quadratic_reward	Boolean(zero false, nonzero true) to use a quadratic reward system in thecontrol loop
quadratic_penalty	Boolean(zero false, nonzero true) to use a quadratic penalty system inthe control loop
use_timeout	Boolean(zero false, nonzero true) to use a timeout when exiting theactive control zone for this client. This helps in smoothinghandoff between LMH and thermal sensors
timeout	如果use_timeout==true，當小于等于set_point時，該算法結束之前將等待'timeout'number of interrupts，feedingreward into the system of value 'set_point' - 'set_point_clr'.
unified_rail	If'unified_rail' is true for any configuration instance of thealgorithm, the unified rail logic of token bucket is applied

■virtual

可以利用兩個以上的Tsensor，通過加權，組成一個虛擬的sensor。8998視頻時間15:20

Strings	說明
algo_type	virtual
trip_sensor	傳感器名稱
set_point	當高于此溫度時，虛擬傳感器開始polling模式
set_point_clr	當高于此溫度時，虛擬傳感器停止polling模式
sensors	用于計算溫度總和的傳感器數組
weights	權重值數組
math	默認值0，使用weigths，可選的，1for minimum of sensors, 2 for max of sensors
sampling	采樣率ms

3.配置文件字段取值解釋

●'thresholds'/'thresholds_clr'/'actions'/'action_info'，最多接受8個空格分開的values

●'actions'field

actions	說明
none	-ACTION - Do nothing -ACTION_INFO - ignored
report	-ACTION - Report threshold crossing to UI -ACTION_INFO - ignored 備注： 通過抽象本地socket"THERMALD_UI"，以每行獨立的string格式，發送thresholdcrossing information。清除或者觸發alevel，或者其他action達到這個level將會導致消息的發送。參數按照以下順序發送 *sensorname - Name of sensor reporting *temperature - Current temperature *current_threshold_level - current threshold level triggered orcleared *is_trigger - "true" on level trigger, "false"on level clearing
cpu	-ACTION - CPU調整cpu頻率 -ACTION_INFO - Max CPU frequency in KHz
cpuN	-ACTION - CPU frequency scaling where N is the specific CPU core[0..MAX CORES] -ACTION_INFO - Max CPU frequency in KHz
clusterN	-ACTION - CLUSTER frequency scaling where N is the specific CLUSTERID -ACTION_INFO - Max CLUSTER frequency in KHz
hotplug_N	-ACTION –拔掉第N個cpu -ACTION_INFO - 0 for online a core, or 1 to offline it.
lcd	-ACTION - LCD brightness throttling，限制lcd的亮度 -ACTION_INFO - 0-255 value for max LCD brightness
modem	-ACTION - Request throttling of modem functionality，請求限制modem功能 -ACTION_INFO - 0-3 throttling level for modem mitigation
fusion	-ACTION - Request throttling of fusion modem functionality -ACTION_INFO - 0-3 throttling level for fusion modem mitigation
battery	-ACTION - Battery charging current throttling -ACTION_INFO - 0-3 throttling level for battery charging current
gpu	-ACTION - GPU frequency scaling -ACTION_INFO - Max GPU frequency in Hz
wlan	-ACTION - WLAN throttling -ACTION_INFO - 0-4 throttling level for WLAN mitigation
shutdown	-ACTION - Shutdown target -ACTION_INFO - Shutdown delay in ms
vdd_ restriction	-ACTION - Request voltage restriction of all vdd rails on SoC -ACTION_INFO - 1 for request for vdd_restriction, 0for release vdd_restriction
camera	-ACTION - camera fps throttling and camera shutdown mitigation -ACTION_INFO - 0-3 throttling level for camera fps mitigation, 10level for camera app shutdown
camcorder	-ACTION - camcorder fps throttling and camcorder shutdownmitigation -ACTION_INFO - 0-3 throttling level for camcorder fps mitigation, 10level for camcorder app shutdown
mdp	-ACTION - Request throttling of MDP CX voting -ACTION_INFO - 0-3 throttling level for MDP mitigation
venus	-ACTION - Request throttling of VENUS CX voting -ACTION_INFO - 0-3 throttling level for VENUS mitigation
modem_cx	-ACTION - Request throttling of modem CX voting -ACTION_INFO - 0-3 throttling level for MODEM CX mitigation

●'device'field

device	說明
cpu	-DEVICE - Dynamic CPU frequency scaling
cpuN	-DEVICE - Dynamic CPU frequency scaling where N is the specific CPUcore [0..MAX CORES]
clusterN	-DEVICE - Dynamic CLUSTER frequency scaling where N is the specificCLUSTER ID
gpu	-DEVICE - Dynamic GPU frequency scaling

4.配置文件示例

例1:

sampling 1000[PMIC_THERM_MON] algo_type monitor sensor PMIC_THERM sampling 5000 thresholds 40200 45000 50000 thresholds_clr 38000 43000 48000 actions cpu+report cpu cpu action_info 1188000+0 368640 245760

描述：

1)默認采樣率為1s；sensorPMIC_THERM設置的采樣率是5s，覆蓋了默認的；

2)當溫度升到40.2度以上時，觸發門限1，調節CPU最大允許頻率為1188000KHz，在本例中，由于此頻率是最大值，因此實際無動作；同時上報此消息，action_info值0被忽略；

3)上升到45度以上時，觸發門限2，下降到43度以下時，清除門限2，調節CPU最大允許頻率為368640 KHz；

4)當門限2在低于43度清除時，調節CPU的最大允許頻率回到1188000KHz上；

5)當門限1在低于38度清除時，產生一個清楚門限1的report，allmitigation被reset。

例2:

debug sampling 2000[PMIC_THERM_MONITOR] algo_type monitor sensor PMIC_THERM sampling 5000 thresholds 40200 45000 50000 thresholds_clr 38000 43000 48000 actions cpu+report cpu report+shutdown action_info 768000+0 368640 0+6000

描述：

1)使能debuglogging輸出；

2)默認采樣率2s，sensorPMIC_THERM的采樣率設置為5s；

3)上升到大于40.2度觸發門限1，下降到低于38度清除門限1，當門限1觸發時，最大允許CPU的頻

率是768000KHz，并且產生一個report(action_infovalue 0 is ignored)；

4)上升到大于45度觸發門限2，下降到低于43度清除門限2，當門限2觸發時，最大允許CPU的頻率

是368640KHz；

5)上升到大于50度觸發門限3，下降到低于48度清除門限3，當門限3觸發時，產生一個report并且

6s后關機。

例3:

debug sampling 2000[bcl_monitor] algo_type monitor descending sensor bcl sampling 1000 thresholds 100 0 thresholds_clr 500 100 actions report report action_info 0 0
描述：

1)使能信息調試輸出；

2)默認采樣率是2s，batterycurrent limit 'bcl'的采樣率設置為1s

3)當ibat上升到(imax- 100mA)時，觸發門限1，當下降到(imax– 500mA)時，清除門限1，When

triggered,generate a report (action_info value 0 is ignored).

4)當ibat上升到imax時，觸發門限2，當下降到(imax– 100mA)時，清除門限2，When

triggered,generate a report (action_info value 0 is ignored).

例4:

debug[TEST_PID] algo_type pid sensor tsens_tz_sensor0 device cpu sampling 1000 set_point 85000 set_point_clr 65000 p_const 1.0 i_const 1.0 d_const 1.0 i_samples 10 dev_units_per_calc10000
描述：

1)使能debuglogging

2)PID算法實例標簽為TEST_PID

3)使用tsens_tz_sensor0傳感器

4)被調節的設備是CPU

5)采樣時間1s

6)set_point值是PID調節算法的門限值和PID算法的設定值；

7)set_point_clr是停止PID調節算法的門限值；

8)p_const, i_const, d_const是PID等式中的p,i,d常量；

9)dev_units_per_calc 10000kHz(kHz unit because this is CPU device) ismultiplied

withPID calculation outcome to determine adjustment on the cpu device.

例5:

debug[virtual-sensor-0] algo_type virtual trip_sensor tsens_tz_sensor8 set_point 35000 set_point_clr 30000 sensors tsens_tz_sensor1 tsens_tz_sensor5 weights 40 60 sampling 250[Test-PID] algo_type pid sensor virtual-sensor-0 device cpu1 sampling 250 set_point 55000 set_point_clr 50000 p_const 1.25 i_const 0.8 d_const 0.5 i_samples 10 dev_units_per_calc5000

描述：

1)PID實例Test-PID基于virtual-sensor-0的結果；

2)virtual-sensor-0需要用戶手動定義；

3)trip_sensor用來指示虛擬傳感器何時開始進入polling模式(輪詢)；

4)trip_sensor必須為常規傳感器，不能為另外一個虛擬傳感器；

5)set_point是tripsensor的門限值，當高于此門限值時，tripsensor將從中斷模式進入輪詢模式，輪詢

頻率由虛擬傳感器的sampling字段設置

6)set_point_clr是tripsensor的門限值，當?shù)陀诖碎T(mén)限值時，tripsensor將停止輪詢模式然后等待下一個

門限事件；

7)sensors定義了常規傳感器數組，這些傳感器要參與權重溫度的計算

8)weights給定了傳感器數組的權重值；

9)虛擬傳感器的set_point必須小于pid算法的set_point，以便當達到set_point時pid能收到通知，另外，

如果虛擬傳感器未進入輪詢模式，pid將不能獲取到它的溫度；

10)如果tirpsensor不支持從中斷模式到查詢模式的改變，第8條可以被忽略。此時虛擬傳感器的采樣率將應該和pid的采樣率一致。

例6:

debug[bcm_monitor] algo_type monitor sensor bcm sampling 1000 thresholds 70000 90000 //注意，單位為m% thresholds_clr 69000 89000 actions cpu cpu action_info 768000 384000
描述：

1)使能debuglogging

2)當采樣電流達到imax的70%時，門限1觸發，調整cpu最大允許頻率為768000KHz；

3)當采樣電流達到imax的90%時，門限2觸發，調整cpu最大允許頻率為384000KHz；

4)bcm僅支持2級門限調節；

5)有效的門限值取值為：40000,50000,60000,70000,80000,90000。

例7:

debug[TB-CPU4] algo_type tb sampling 10 sensor tsens_tz_sensor13 device cluster1 set_point 85000 set_point_clr 50000 time_constant 1 up_loop_gain 2 down_loop_gain 3 auto_penalty 1.0 auto_reward 0.0 temp_scale_factor 1000 freq_scale_factor 1 quadratic_reward 1 quadratic_penalty 1 use_timeout 0 timeout 1

1)使能debuglogging；

2)我們配置CPU4被tokenbucket控制。由于算法是tb，sensor是tsens_tz_sensor13，device是cluster1，

這個instance將monitortsens_tz_sensor13并且控制cluster1的頻率；

3)每10ms發生一次溫度讀取和頻率mitigation

4)當溫度上升到85度時，將觸摸3)事件，溫度下降到50度時clr

5)time_constant is currently unused but is reserved for futureuse.當前使用，為未來使用保留

6)up_loop_gain set to 2 means that for every degree thattsens_tz_sensor13 is below its set_point, the reward
willincrease by a factor of 2. --2倍

7)down_loop_gain set to 3 means that for every degree thattsens_tz_sensor13 overshoots its set_point, the

penalty willincrease by a factor of 3. --3倍

8)auto_penalty of 1.0 means that the number of degrees of overshootused to calculate penalty will always be

incrementedby 1.0. This means that at 85C, the temperature overshoot will be 1C,86C->2C, etc.

9)auto_reward of 0.0 means that the number of degrees of undershootused to calculate the reward will not be

augmented.This means that at 80C, the temperature undershoot will be 5C,81C->4C, etc.

10)temp_scale_factorof 1000 means that the temperature readings from tsens_tz_sensor13are received in mC

andnot C. This used to vary between tsens sensors and other types ofsensors in the thermal-engine such as

gensensors.

11)freq_scale_factorof 1 means that the frequency readings from device1 are recieved inkHz. This varies

betweendevices, for instance the GPU frequency readings on 8994 are receivedin Hz, and therefore the

freq_scale_factorfor the 8994 GPU is 1000.

12)quadratic_rewardof 1 means to square the amount of reward. Whereas reward wouldnormally be

(undershoot *up_loop_gain), if this value is nonzero then reward is calculated as(undershoot *

up_loop_gain)^2.

13)quadratic_penaltyof 1 means to square the amount of penalty. Whereas penaltywouldnormally be

(overshoot *down_loop_gain), if this value is nonzero then penalty is calculatedas (overshoot *

down_loop_gain)^2.

14)use_timeoutof 0 means that when the readings on tsens_tz_sensor13 reach theirset_point_clr, the algorithm

shouldimmediately stop polling and stop mitigating. If this value werenonzero, then the algorithm would

wait fortimeout number of sequential interrupts (i.e. timeout * sampling ms)in which the reading from

tsens_tz_sensor13was below set_point_clr before ceasing to poll and mitigate.

5. 加載

關于sperakercall：80-N9649-1_D中的內容，ThermalCalibration Procedure for Speaker Coil Protection

speakercoil(線圈)的thermal校準的目標是準確的測量出來自溫度傳感器中的speakercoil的溫度

可以通過三步實現：

1.轉換resistanceto temperature –通過實際測量找出他們之間的線性關系b= T- mR

2.決定thermalmanagement algorithm中的offsetvalue – 查看logcat顯示最小溫度32度，實際萬用表測量是27度，那么offset= 27 -32 = -5度

3.Program offset into device –這個是thermal-engine-o輸出sperker-cal內容

[SPEAKER-CAL] sampling30000 30000 10 1800000 sensorpm8953_tz sensorstsens_tz_sensor1 tsens_tz_sensor2 tsens_tz_sensor3 tsens_tz_sensor14tsens_tz_sensor15 temp_range6000 10000 2000 max_temp45000 offset-4000

已經定義的宏，ANDROID

未定以的宏，ENABLE_OLD_PARSER

thermal.c

structthermal_setting_tthermal_settings;//包含一個setting_info鏈表，它包含關于thermal算法的基本數據 intmain(int argc, char **argv) { … if(!config_file) { if((config_file = get_target_default_thermal_config_file())) info("Usingtarget config file '%s'\n", config_file); else//這條路system/etc/thermal-engine.conf info("Notarget config file, falling back to '%s'\n", CONFIG_FILE_DEFAULT); } if(output_conf) {//thermal-engine -o，dumpconfig file of active settings devices_manager_init(); devices_init(minimum_mode); sensors_manager_init(); ... return 0; } … devices_manager_init();//啥也沒做 devices_init(minimum_mode);//通過讀取sys節點信息，初始化gpufreq、cpufreq、clusterfreq、 thermal_ioctl、qmi_communication、各種dev、vdd*、profile_switch、lcd、battery_mitigation等等 target_algo_init();///*Vote to keep kernel mitigation enabled until init is done */ kernel_dev =devices_manager_reg_clnt("kernel");//獲取/sys/kernel/下的節點信息，并且組裝成鏈表 if(kernel_dev == NULL) { msg("%sFailed to create kernel device handle\n", __func__); } req.value =1; device_clnt_request(kernel_dev,&req);sensors_manager_init//啥也沒做 sensors_init(minimum_mode);//1.通過/sys/module/msm_thermal/sensor_info開始初始化sensors[]， 2./sys/devices/virtual/thermal/thermal_zone*，繼續初始化sensors[]， 3.將bcl加入structsensors_mgr_sensor_info *sensor_list if(thermal_algo_framework_init() != THERMAL_ALGO_SUCCESS){//thermal_threads = NULL; info("%s:Error initializing thermal algorithm framework", __func__); return 1; }init_settings(&thermal_settings);//清0 pid_init_data(&thermal_settings);//初始化定義好的pid數據，加入thermal_settings.setting_info里 thermal_monitor_init_data(&thermal_settings);//monitor speaker_cal_init_data(&thermal_settings); ss_init_data(&thermal_settings); tb_init_data(&thermal_settings);virtual_sensors_init_data(&thermal_settings); virtual_sensors_init(&thermal_settings,config_file);//初始化并且loadconfig_file數據到虛擬傳感器鏈表load_config(&thermal_settings,config_file, LOAD_ALL_FLAG);//thermal_config_v2.cthermal_server_init(); /*創建4個server套接字，并且使用select方法監聽 1.sockfd_server_send，通知已經注冊client端thermalcurrent level 2.sockfd_server_recv，獲得client發送數據，并調用callback相應更新，在pid、montior、speaker、ss后面等初始化時加入了callback 3.sockfd_server_log，將獲得與客戶端鏈接的新fd加入socket_fd[MAX_SOCKET_FD] 4.sockfd_server_recv_passive，清緩存，清除select描述符集，清除thermal_send_fds[]，里面存儲了每次新連接的clientfd */ pid_algo_init(&thermal_settings);//初始化pid，并且開啟線程pid_algo_monitor thermal_monitor(&thermal_settings); ss_algo_init(&thermal_settings); speaker_cal_init(&thermal_settings); if(tb_algo_init(&thermal_settings) != THERMAL_ALGO_SUCCESS) { info("%s:Error initializing token bucket", __func__); return 1; } if(kernel_dev) device_clnt_cancel_request(kernel_dev); while (1) pause(); ...//釋放資源 }

總結

以上是生活随笔為你收集整理的高通Thermal Overview之thermal-engine的全部?jī)?nèi)容，希望文章能夠幫你解決所遇到的問題。

如果覺得生活随笔網站內容還不錯，歡迎將生活随笔推薦給好友。