k64 datasheet学习笔记45---10/100-Mbps Ethernet MAC(ENET)之功能描述
1.前言
本文是對K64 datasheet 之ENET部分的功能描述,將對每個部分進行詳細說明
2.Ethernet MAC frame formats
MAC幀組成格式
(1)7字節前導碼:如按最低位先傳則為0x55 0x550x550x550x550x55;
(2)起始幀定界符(SFD):如按最低位先傳則為0XD5;
(3)2個地址域:包括源MAC地址和目的MAC地址;
(4)VLAN-tagged :可選,占4字節
(5)長度或類型域:代表有效負荷的長度或者類型,以太網802.3組幀為例,如果小于0X05DC(1500字節)則為長度信息,如果大于0X0600(1536字節)則為類型信息
常見的類型為:IPV4,ARP等
(6)有效載荷:最小為42 octets(帶有VALAN-tagged),46 octets(不帶有VALAN-tagged),最大載荷為1500 octets
(7)填充域:有效載荷不足42 octets(帶有VALAN-tagged),46 octets(不帶有VALAN-tagged),則填充
(8)CRC值:4字節循環冗余校驗
注:
[1]幀長度不包括Preamble和SFD,幀最小長度為64字節,最大長度為1518字節
[2]除去 6 octets的 Destination address+6 octsts Source address+2 octets Length/type+4octets FCS = 18 octets,因此有效載荷需要至少46 octets,需填充0~46octets
[3]可選的是VLAN-tagged 可以插入到MACSource address和Length/type之間4字節,構成VLAN-tagged MAC 幀
MAC幀定義
Pause Frames
接收端產生一個pause frame指示當前傳輸遇到擁堵,發送端需要停止發送數據
Magic packets
用于實現遠程喚醒,當偵測到magic packet,主機會被喚醒
3.IP and higher layers frame format
舉例來說IP數據報指定了Ethernet幀的有效負荷,TCP數據報又在IP數據報中指定了有效負荷
Ethernet types
IPv4 datagram format
IPv6 datagram format
Internet Control Message Protocol (ICMP) datagram format
User Datagram Protocol (UDP) datagram format
TCP datagram format
4. IEEE 1588 message formats
Adjustable timer module
ENET時間戳?xí)r鐘源既可以來自外部ENET_1588_CLKIN PAD ,也可以來自內部ENET PLL 。最好選擇整形值如3ns產生精準計時
通過專用校準邏輯定時器被校準來同步遠端master時鐘作為本地系統的參考時鐘
Adjustable timer implementation
Transmit timestamping
Receive timestamping
Time synchronization
5. MAC receive
Collision detection in half-duplex mode
Preamble processing
MAC core允許任意長度的preample,也允許是0長度,如果preample后SFD的首個字節不是0x55也不是0xd5則丟棄
MAC address check
目的地址bit0區分了不同的地址:
(1)If bit 0 is 0, the MAC address is an individual (unicast) address.
(2)If bit 0 is 1, the MAC address defines a group (multicast) address.
(3)If all 48 bits of the MAC address are set, it indicates a broadcast address.
Frame length/type verification: payload length check
If the length/type is less than 0x600 and NLC is set, the MAC checks the payload lengthand reports any error in the frame status word and interrupt bit PLR
If the length/type is greater than or equal to 0x600, the MAC interprets the field as a typeand no payload length check is performed
The length check is performed on VLAN and stacked VLAN frames. If a padded frame isreceived, no length check can be performed
Frame length/type verification: frame length check
When the receive frame length exceeds MAX_FL bytes, the BABR interrupt is generatedand the RxBD[LG] bit is set.
VLAN frames processing
VLAN frames have a length/type field set to 0x8100 immediately followed by a 16-BitVLAN control information field.
Pause frame termination
The receive engine terminates pause frames and does not transfer them to the receiveFIFO
CRC check
The CRC-32 field is checked and forwarded to the core FIFO interface ifENETn_RCR[CRCFWD] is cleared and ENETn_RCR[PADEN] is set
Frame padding removal
Recieve flushing
RX flushing prevents frames in the RX FIFO from being blocked
6 MAC transmit
Frame payload padding
The IEEE specification defines a minimum frame length of 64 bytes
MAC address insertion
CRC-32 generation
Inter-packet gap (IPG)
Collision detection and handling — half-duplex operationonly
A collision occurs on a half-duplex network when concurrent transmissions from two ormore nodes take place.
7. Full-duplex flow control operation
8 Magic packet detection
Magic packet detection wakes a node that is put in power-down mode by the nodemanagement agent
9. IP accelerator functions
Checksum calculation
The IP and ICMP, TCP, UDP checksums are calculated with one's complementarithmetic summing up 16-bit values
Additional padding processing
32-bit Ethernet payload alignment
The data FIFOs allow inserting two additional arbitrary bytes in front of a frame. Thisextends the 14-byte Ethernet header to a 16-byte header, which leads to alignment of the
Ethernet payload
IPv4 fragments
IPv6 support
10. Resets and stop controls
Hardware reset
Soft reset
Hardware freeze
Graceful stop
During a graceful stop, any currently ongoing transactions are completed normally andno further frames are accepted
11 IEEE 1588 functions
Adjustable timer module
Transmit timestamping
Receive timestamping
Time synchronization
12 FIFO thresholds
Receive FIFO
Transmit FIFO
13 Loopback options
14 Legacy buffer descriptors
To support the Ethernet controller on previous Freescale devices, legacy FEC buffer descriptors are available
15 Enhanced buffer descriptors
This section provides a description of the enhanced operation of the driver/DMA via thebuffer descriptors
16 Client FIFO application interface
The FIFO interface is completely asynchronous from the Ethernet line, and the transmitand receive interface can operate at a different clock rate
17 FIFO protection
Transmit FIFO underflow
Transmit FIFO overflow
Receive FIFO overflow
18 Reference clock
The input clocks to the ENET module must meet the specifications in the following table
19 PHY management interface
MDIO frame format
MDIO clock generation
The MDC clock is generated from the internal bus clock divided by the valueprogrammed in ENETn_MSCR[MII_SPEED].
MDIO operation
To perform an MDIO access, set the MDIO command register (ENETn_MMFR)according to the description provided in MII Management Frame Register(ENETn_MMFR).
To check when the programmed access completes, read the ENETn_EIR[MII] field.
20 Ethernet interfaces
The following Ethernet interfaces are implemented:
-Fast Ethernet MII (Media Independent Interface)
-RMII 10/100 using interface converters/gaskets
The following table shows how to configure ENET registers to select each interface
RMII interface
MII Interface — transmit
MII interface — receive
總結
以上是生活随笔為你收集整理的k64 datasheet学习笔记45---10/100-Mbps Ethernet MAC(ENET)之功能描述的全部?jī)?nèi)容,希望文章能夠幫你解決所遇到的問題。
- 上一篇: 判定覆盖和条件覆盖的区别(条件/判定覆盖
- 下一篇: 专访李智慧:架构是最高层次的规划和难以改