這是以前學32的時候?qū)懙?#xff0c;那時候?qū)W了32之后感覺32真是太強大了，比51強的沒影。關于dma網上有許多的資料，關于dma采集ad網上也有很多。親們搜搜，這里只貼代碼了，其實我也想詳詳細細地?cái)⑹鲆环?#xff0c;但是自己本身打字就慢，還有好多事情要做！代碼是我親自都在板子上測試過的，，當然粘貼/復制過去可能也不會盡如人意，知識這東西總是有許多道不清說不明的東西在里頭，往往總是不經一番徹骨寒，哪得梅花撲鼻香。推薦一本書吧！這是野火出的。

這本書自從在圖書館借來就從來沒有再放回去，總是在續借。像是在打廣告了

#include <stm32f10x.h> #include "ADC1.h" #include "DMA1.h" #include "USART1.h" #include "time.h" #include "stdio.h"extern uint32_t SendBuff; float ADC_Received; uint32_t ADC_Received1; uint8_t ADC_Received2[11];//printf函數重新定向，方便在程序中使用 int fputc(int ch, FILE *f) { USART_SendData(USART1, (unsigned char) ch);while (!(USART1->SR & USART_FLAG_TXE)); return (ch); }void usart_putchar(uint8_t ch) {USART_SendData(USART1,ch);while(USART_GetFlagStatus(USART1,USART_FLAG_TXE) == RESET); }int main() {ADC1_Config();DMA_Config();USART1_Config();while(1){// ADC_Received = (float)ADC_GetConversionValue(ADC1)*3.3/4069; // ADC_Received1 = ADC_Received * 1000000000; ADC_Received = (float)SendBuff*3.3/4069;ADC_Received1 = ADC_Received * 1000000000;ADC_Received2[0]=(ADC_Received1/1000000000 + 0x30);//usart_putchar(0x2e); ADC_Received2[1]=(ADC_Received1%1000000000/100000000 + 0x30);ADC_Received2[2]=(ADC_Received1%1000000000%100000000/10000000 + 0x30);ADC_Received2[3]=(ADC_Received1%1000000000%100000000%10000000/1000000 + 0x30);ADC_Received2[4]=(ADC_Received1%1000000000%100000000%10000000%1000000/100000 + 0x30);ADC_Received2[5]=(ADC_Received1%1000000000%100000000%10000000%1000000%100000/10000 + 0x30); ADC_Received2[6]=(ADC_Received1%1000000000%100000000%10000000%1000000%100000%10000/1000 + 0x30); ADC_Received2[7]=(ADC_Received1%1000000000%100000000%10000000%1000000%100000%10000%1000/100 + 0x30); ADC_Received2[8]=(ADC_Received1%1000000000%100000000%10000000%1000000%100000%10000%1000%100/10 + 0x30); ADC_Received2[9]=(ADC_Received1%10 + 0x30);ADC_Received2[10]=0x0d;USART_DMACmd(USART1, USART_DMAReq_Tx, ENABLE); // delay_ms(1000); // USART_DMACmd(USART1, USART_DMAReq_Tx, DISABLE); // delay_ms(1000); // ADC_Received = (float) SendBuff/4069*3.3;// ADC_Received = (u16)ADC1 -> DR; // ADC_Received = (float)ADC_Received/4069*3.3; // printf("\r\n v = %f V \r\n",ADC_Received); // while(!ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC ));// usart_putchar('\r'); // usart_putchar('\n'); // usart_putchar(0x0d); // usart_putchar(0x0a); // printf("\r"); // printf("\n"); // printf("\r\n V = %fv\r\n",ADC_Received); } } #include "ADC1.h"void ADC1_Config(void) {ADC_InitTypeDef ADC_InitStructure;RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);ADC1_Gpio_Config();ADC_DeInit(ADC1); //復位 ADC1,將外設 ADC1 的全部寄存器重設為缺省值// ADC1 配置ADC_InitStructure.ADC_Mode = ADC_Mode_Independent; //ADC1工作在獨立模式ADC_InitStructure.ADC_ScanConvMode = ENABLE;//使能掃描ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;;//ADC轉換工作在連續模式ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;//由軟件控制轉換ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;//轉換數據右對齊ADC_InitStructure.ADC_NbrOfChannel = 1;//轉換通道為通道1ADC_Init(ADC1, &ADC_InitStructure); //初始化ADC //ADC1選擇信道0,順續等級1,采樣時間239.5個周期ADC_RegularChannelConfig(ADC1, ADC_Channel_0, 1, ADC_SampleTime_28Cycles5); //打開ADC1 ADC_Cmd(ADC1, ENABLE);//重置ADC1校準寄存器 ADC_ResetCalibration(ADC1); //等待ADC1校準重置完成while(ADC_GetResetCalibrationStatus(ADC1)); //開始ADC1校準 ADC_StartCalibration(ADC1); //等待ADC1校準完成while(ADC_GetCalibrationStatus(ADC1)); //使能ADC1軟件開始轉換 ADC_SoftwareStartConvCmd(ADC1, ENABLE);//配置ADC時鐘=PCLK2 1/6 12MHz RCC_ADCCLKConfig(RCC_PCLK2_Div6); //使能ADC1模塊DMA ADC_DMACmd(ADC1, ENABLE); }static void ADC1_Gpio_Config(void) {GPIO_InitTypeDef GPIO_InitStructure;RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;GPIO_Init(GPIOA , &GPIO_InitStructure);} #include "DMA1.h"/* 其他函數里 USART_DMACmd(USART1, USART_DMAReq_Tx, ENABLE); */ uint32_t SendBuff; extern float ADC_Received; extern uint8_t ADC_Received2[11]; //描述 ：DMA 串口的初始化配置void DMA_Config(void) {//初始化結構體 DMA_InitTypeDef DMA_InitStructure;//開啟DMA時鐘 RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE); //配置DMA中斷 NVIC_Config(); //設置DMA源：地址 DMA_InitStructure.DMA_PeripheralBaseAddr = (u32)&ADC1 -> DR; //*內存地址(要傳輸?shù)淖兞康闹羔?DMA_InitStructure.DMA_MemoryBaseAddr = (u32)&SendBuff;//外設作為數據傳輸?shù)膩碓?/span>DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC; //指定 DMA 通道的 DMA 緩存的大小，單位為數據單位。DMA_InitStructure.DMA_BufferSize = 1;//*外設地址不增 DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable; //*內存地址不增DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Disable; //*外設數據單位數據寬度為 16 位DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord;//*內存數據單位數據寬度為 16 位DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord; //*DMA模式：一次傳輸/循環 // DMA_Mode_Circular 工作在循環緩存模式 // DMA_Mode_Normal 工作在正常緩存模式 // DMA_InitStructure.DMA_Mode = DMA_Mode_Normal ; DMA_InitStructure.DMA_Mode = DMA_Mode_Circular; //*優先級：高DMA_InitStructure.DMA_Priority = DMA_Priority_High; //*禁止內存到內存的傳輸 DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;//*配置DMA1的1通道 DMA_Init(DMA1_Channel1, &DMA_InitStructure); //使能DMA DMA_Cmd (DMA1_Channel1,ENABLE);//配置DMA發送完成后產生中斷 // DMA_ITConfig(DMA1_Channel1,DMA_IT_TC,ENABLE); //****************************************************/// //****************************************************/// //****************************************************/////設置DMA源：地址DMA_InitStructure.DMA_PeripheralBaseAddr = (u32)&USART1 -> DR; //*內存地址(要傳輸?shù)淖兞康闹羔?DMA_InitStructure.DMA_MemoryBaseAddr = (u32)ADC_Received2;//外設作為數據傳輸?shù)哪康牡?/span>DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST; //指定 DMA 通道的 DMA 緩存的大小，單位為數據單位。DMA_InitStructure.DMA_BufferSize = 11;//*外設地址不增 DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable; //*內存地址不增DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable; //*外設數據單位數據寬度為 16 位DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;//*內存數據單位數據寬度為 16 位DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte; //*DMA模式：一次傳輸/循環 // DMA_Mode_Circular 工作在循環緩存模式 // DMA_Mode_Normal 工作在正常緩存模式 // DMA_InitStructure.DMA_Mode = DMA_Mode_Normal ; DMA_InitStructure.DMA_Mode = DMA_Mode_Circular; //*優先級：中DMA_InitStructure.DMA_Priority = DMA_Priority_Medium; //*禁止內存到內存的傳輸 DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;//*配置DMA1的4通道 DMA_Init(DMA1_Channel4, &DMA_InitStructure); //使能DMA DMA_Cmd (DMA1_Channel4,ENABLE);//配置DMA發送完成后產生中斷 // DMA_ITConfig(DMA1_Channel1,DMA_IT_TC,ENABLE); } #include "time.h"/**************** 延時多少個 1/72 us ****************/ void delay_1_72us(uint32_t time) {SysTick -> LOAD = (u32) time; //定時器賦初值 SysTick -> CTRL = 0x00000005; //選擇72MHz 并 打開定時器while(!(SysTick -> CTRL & 0x00010000));//等待計數到零 SysTick -> CTRL = 0x00000004;//關閉定時器 }void delay_ms(u32 time) {while(time -- ){delay_1_72us(72000);}} #include "USART1.h"//描述 ：USART1 GPIO 配置,工作模式配置。115200 8-N-1void USART1_Config(void) {GPIO_InitTypeDef GPIO_InitStructure;USART_InitTypeDef USART_InitStructure;// 打開 USART1 的時鐘RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 | RCC_APB2Periph_GPIOA, ENABLE);// USART1 Tx (PA_9) GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;//復用推挽輸出GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;GPIO_Init(GPIOA, &GPIO_InitStructure); // USART1 Tx (PA_10) GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;//浮空輸入GPIO_Init(GPIOA, &GPIO_InitStructure);/* USART1 mode config */USART_InitStructure.USART_BaudRate = 115200;USART_InitStructure.USART_WordLength = USART_WordLength_8b;USART_InitStructure.USART_StopBits = USART_StopBits_1;USART_InitStructure.USART_Parity = USART_Parity_No ;USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;USART_Init(USART1, &USART_InitStructure); USART_Cmd(USART1, ENABLE); }

?

轉載于:https://www.cnblogs.com/yangfengwu/p/5297147.html

總結

以上是生活随笔為你收集整理的stm32_DMA采集一个AD数据_并通过DMA向串口发送的全部內容，希望文章能夠幫你解決所遇到的問題。

如果覺得生活随笔網站內容還不錯，歡迎將生活随笔推薦給好友。