Call流程

無論是在CS還是ims域看掉話問題首先先分析是否校準以及寫入IMEI號

在 kernel-3.18及其以前的老平臺中可以通過隨機接入來分析DUT是否有校準，如果信號還算良好，但頻繁隨機接入失敗。那么可能是沒有校準或rf參數本身有問題。
典型log如下
1403508, 947548, 884529, 18:05:45:610 2018/02/27, MOD_UMAC, , TRACE_INFO, rachSuccess = 0, rachFail = 1
1404675, 947836, 884795, 18:05:46:810 2018/02/27, MOD_UMAC, , TRACE_INFO, rachSuccess = 0, rachFail = 2
1405841, 948118, 885055, 18:05:48:210 2018/02/27, MOD_UMAC, , TRACE_INFO, rachSuccess = 0, rachFail = 3
1409412, 948410, 885325, 18:05:49:610 2018/02/27, MOD_UMAC, , TRACE_INFO, rachSuccess = 0, rachFail = 4
1410642, 948696, 885589, 18:05:50:810 2018/02/27, MOD_UMAC, , TRACE_INFO, rachSuccess = 0, rachFail = 5

在kernel-4.4的新平臺中，可通過如下log判斷DUT是否校準
500119, 12125, 1256221, 16:46:43:794 2017/12/27, MOD_NIL, , TRACE_INFO, 4G calibration is not performed or the calibration data is not downloaded !!!
500134, 12125, 1256221, 16:46:43:794 2017/12/27, MOD_NIL, , TRACE_INFO, 2G calibration is not performed or the calibration data is not downloaded !!!
500135, 12125, 1256221, 16:46:43:794 2017/12/27, MOD_NIL, , TRACE_INFO, 3G calibration is not performed or the calibration data is not downloaded !!!

GPRS會發起鑒權要求UE提供IMEI號以驗證UE是否合法，如果沒有合法IMEI號會被網絡拒絕接入,會無服務或者掉話

GPRS鑒權被拒，例如：
從mdlog的system trace里查看到?jīng)]寫入IMEI,
Message: IMEI of SIM1:ffffffffffffff0
在mdlog的Trace peer window查看到GPRS鑒權時被拒
MOD_MM TRACE_PEER [NW->MS] GMM__AUTHENTICATION_AND_CIPHERING_REJ

2 寫了IMEI，但是不合法，在Location update時被網絡以Illegal ME拒絕，
Frame #: Time: 939835 Local Time: 14:37:43:719 2014/09/11 Message: IMEI of SIM1:865627022306010
2273 Trace 940141 14:37:45:131 2014/09/11 MOD_MM TRACE_PEER [NW->MS] MM__LOCATION_UPDATING_REJECT
2275 Trace 940141 14:37:45:131 2014/09/11 MOD_MM TRACE_INFO Location Update is rejected with cause ILLEGAL_ME

在校準和imei號都o(jì)k后，在開始分析流程，主要分析OTA messages

2G/3Gcall總體流程

MOC流程（MIC類似）
Step1 ：CM service request //call請求
Step2 ：RA and immediate assignment //隨機接入。立即指派
Step3 ：MM connection setup //mm連接建立
Step4 ：MM assignment for MOC//RR分配

具體log流程
mo call流程
[MS->NW] MM__CM_SERVICE_REQUEST //申請call請求
[NW->MS] RR__IMMEDIATE_ASSIGNMEN
[MS->NW] RR_CHANNEL_REQUEST
[MS->NW] CC__SETUP
[NW->MS] CC__CALL_PROCEEDING//網絡對端收到paging
[NW->MS] CC__ALERTING //收到對端鈴聲
[NW->MS] CC__CONNECT
[MS->NW] CC__CONNECT_ACKNOWLEDGE

MT call
[MS->NW] RR__PAGING_RESPONSE
[NW->MS] RR__IMMEDIATE_ASSIGNMENT
[NW->MS] CC__SETUP
[MS->NW] CC__CALL_CONFIRMED
[MS->NW] CC__ALERTING//向?qū)Χ税l(fā)起鈴聲
[MS->NW] CC__CONNECT
[NW->MS] CC__CONNECT_ACKNOWLEDGE

主動掛斷流程
[MS->NW] CC__DISCONNECT
[NW->MS] CC__RELEASE
[MS->NW] CC__RELEASE_COMPLET

Calldrop常見原因

若是在CC__CONNECT后異常calldrop需要確定在以上流程哪個步驟出現異常。

首先應該check是否收到NW下發的CC__DISCONNECT，如果有收到，很可能是對端或者網絡問題
之后就需要看nw下發的CC__DISCONNECT帶的cause_value 是多少來確定掛斷原因，進一步分析對端log。詳細的cause_value含義可以參考以下文檔
https://wenku.baidu.com/view/2c6dc83b31126edb6f1a106b.html

如果沒有收到CC__DISCONNECT那么需要check call中斷的地方，即不在上報[MS->NW] RR__MEASUREMENT_REPORT的時間節點附近的PS integreted

首先可以看MAX RLC: 64 CURRENT RLC: 0 如果max rlc不等于current rlc說明網絡丟包，當current rlc減小到10以下就很容易掉話

掉話原因可以查看MSG_ID_LAPDM_RR_ERROR_IND附帶的error_cause
具體的error_cause可在百度中找到，通常掉話原因都是以下兩種cause
error_cause = ERROR_TIMER_EXPD_N200_ABNORMAL_REL (enum 2)
error_cause = ERROR_RADIO_LINK_FAILURE (enum 19)

第一個cause是N200定時器超時，即UE多次回復RR__MEASUREMENT_REPORT，NW不會因
第二個cause是radio link fail主要體現在RLC丟包

造成以上兩個原因基本上都是信號質量不好造成的，可以看MSG_ID_MPAL_RR_SERV_DEDI_MEAS_IND信令中附帶的
rlac_sub_in_quarter_dbm = 0xfeab，信號強度
rxqual_sub_avg = 0x07信號質量，0最優，7最差

小區切換fail引起的 calldrop或者通話無聲問題
通常可以看到信號質量rxqual_sub_avg 在5或5以上（除了7，7可能就直接掉了）網絡會要求UE切換小區，下發RR__HANDOVER_COMMAND
[RMC] Target_arfcn = 656, F_O = 1169239, E_O = 7924
MSG_ID_MPAL_RR_HANDOVER_FAIL_IND
MSG_ID_RR_LAPDM_RECON_REQ
T3124計時器超時，因?yàn)樾盘?hào)質量已經太差了，比如在車上，網絡在5的時候發起handover，真正 還是的時候，信號質量已經7了。之后UE通常會請求重新駐網會原來小區
[MS->NW] RR__HANDOVER_FAILURE Abnormal release, timer expired (3)
如果成功回去，那么這就是一個NW引起的通話無聲問題通話
如果回不去了，那么就是一個NW引起的掉話問題

信號質量差，去尋找能駐留的小區，但是發現沒有適合的小區造成的掉話
[MS->NW] RR__MEASUREMENT_REPORT
MSG_ID_LAPDM_RR_ERROR_IND
//信號質量差導致Radio Link Failure錯誤
MSG_ID_LAPDM_RR_ERROR_IND
//channel斷開
RRM - MPAL MSG_ID_RR_MPAL_DEDICATED_CHANNEL_DISCONNECT_REQ
MPAL - RRM MSG_ID_MPAL_RR_DEDICATED_CHANNEL_DISCONNECT_CNF
RRM - RATCM MSG_ID_RATCM_GAS_CONN_LOSS_IND
RRM [RMC] Radio Link Trigger reselection!
RATCM - MM MSG_ID_MM_RATCM_CONN_LOSS_IND
MM CM rej because RADIO LINK FAILURE
//嘗試重建call
MM_WAIT_FOR_REESTABLISH
CC ENTER RE-ESTABLISHMENT MODE
RRM [NW->MS] RR__SI_2 (ARFCN[123], TC[1])
[NW->MS] RR__SI_2 (ARFCN[648], TC[1])
[NW->MS] RR__SI_2TER (ARFCN[120], TC[5])
[NW->MS] RR__SI_4 (ARFCN[118], TC[7])
[NW->MS] RR__SI_2 (ARFCN[118], TC[1])

//沒有合適小區進行重建call，放棄重建，報告通話中斷。
MM_IDLE_NO_CELL_AVAILABLE
MSG_ID_MNCC_REL_CNF
MSG_ID_L4CCSM_CC_ABORT_CALL_REQ

若是call雜音斷續等問題，可以聽vmlog來check是聲音否有問題，同時從RLC是否有丟包兩點來analyse是audio 還是modem的問題 。

若發現是上述原因掉話，需要確定對比機是否pass，如果對比機pass，那么看對比機和問題機是否在同一個arfcn，如果在同一個arfcn，需要請rf部門同事確認天線及其rf性能為何不如對比機。若發現不在同一個arfcn，需要check全部的arfcn，看看我們的機器所有小區的信號和對比機有什么區別，來做具體分析,具體log可以看，[RMC][MR][2G]: NCEEL Report[0] -> arfcn[108], rla[-374]，通常是一次測5個最好的小區。

長時間掛不掉call
主動掛斷ue發出CC__ALERTING，但是網絡沒有下發[NW->MS] CC__CONNECT_ACKNOWLEDGE造成的長時間掛不掉電話，體現在一直卡在撥號界面顯示正在掛斷
之前見過的是在MSG_ID_LAPDM_RR_ERROR_IND中有附帶
ERROR_TIMER_EXPD_N200_ABNORMAL_REL

Call fail常見問題

主要看掛在在哪個步驟上

沒有發起1CSFB后立刻fail
//下paging
[NW->MS] PAGING,
PagingRecordList[KAL_TRUE], SIB Modification[KAL_FALSE], ETWS[KAL_FALSE], CMAS[KAL_FALSE]
CS的paging
ERRC_CEL [CEL_DI/LV] send PAGING_IND to EMM on [ENASAS_CN_DOMAIN_CS] with STMSI(mmec/mtmsi)[164/236,140,61,5]
PS 1546786 487939 14:53:13:455 EMM_ERRCIF [EMM ERRCIF] Receive CS STMSI paging
那么CSFB到2G
[MS->NW] EMM_
_Service_Request(service type=“MT_CSFB”, CSFB response=“CSFB_ACCEPTED_BY_UE”)
RRM [MS->NW] RR__PAGING_RESPONSE
RRM [NW->MS] RR__SI_6 (ARFCN[76], TC[255])
RRM [MS->NW] RR__MEASUREMENT_REPORT
發生了N200錯誤
RRM MSG_ID_LAPDM_RR_ERROR_IND
error_cause = ERROR_TIMER_EXPD_N200_ABNORMAL_REL (enum 2)

有發起1、[MS->NW] MM__CM_SERVICE_REQUEST
但是沒有收到nw的[NW->MS] RR__IMMEDIATE_ASSIGNMEN后來被UE主動釋放
[MS->NW] RRC__SIGNALLING_CONNECTION_RELEASE_INDICATION
如果頻繁發生在此階段，信號頻繁變化，那么可能需要檢查rf參數RX配置是否有問題，如果信號穩定，那么可能需要檢查rf參數TX是否有問題，如果偶先，可能是nw問題

如果收到[NW->MS] RR__IMMEDIATE_ASSIGNMEN隨后收到網絡下發[NW->MS] MM__ABORT，那么可能是MT的問題，需要check MT

如果在收到[NW->MS] CC__CALL_PROCEEDING，[NW->MS] CC__ALERTING之后掛斷，那么同樣也需要check對端，因?yàn)槿绻麑?duì)端有問題，UE這邊可能會收到，您所撥打的電話…之類的

如果剛一接聽就自動掛斷，MO,MT都收到網絡下發的CC__DISCONNECT，那么需要具體看其帶的cause_value，目前有見過最多的value是44，如果不是很頻繁，通常是網絡異常；如果很頻繁需要check ANT性能

關于何時下paging，合適進入active？

具體call AP和modem的狀態同步，即什么時候進入active，什么時候進入idle，需要查看3GPP 24.008，百度3GPP可以自行下載

關于paging類型，何時下paging，在25.331中有詳細介紹

4G call流程

[MRM] store scell: earfcn[37900] pci[87] rsrp[-433] rsrq[-50] cell_off[0] cell_state[0]
[MRM] store scell: earfcn[37900] pci[87] rsrp[-433] rsrq[-49] cell_off[0] cell_state[0]
PS域?qū)儆跇I(yè)務相關的paging
OTA 1603090 493571 14:53:41:615 ERRC_CEL [NW->MS] PAGING, PagingRecordList[KAL_TRUE], SIB Modification[KAL_FALSE], ETWS[KAL_FALSE], CMAS[KAL_FALSE]
PS 1603102 493571 14:53:41:615 ERRC_CEL [PAGING] Rx Paging for UE with S-TMSI: mmec[10100100b], m-tmsi:[11101100b 10001110b 00111101b 00000101b]
PS 1603103 493571 14:53:41:615 ERRC_CEL [PAGING] ueid matched?[KAL_TRUE]: sim_status[ENASAS_SIM_VALID], ueid sel[PagingUE_Identity_s_TMSI_selected], stmsi_valid in SIM[KAL_TRUE]
PS 1603104 493571 14:53:41:615 ERRC_CEL [CEL_DI/LV] send PAGING_IND to EMM on [ENASAS_CN_DOMAIN_PS] with STMSI(mmec/mtmsi)[164/236,142,61,5]
PS 1603105 493571 14:53:41:615 ERRC - EMM MSG_ID_EMM_ERRC_PAGE_IND
完成PS域相關的網絡需要
OTA 1603727 493576 14:53:41:615 ERRC_CONN [MS->NW] ERRC_RRCConnectionRequest
PS 1609305 493633 14:53:41:815 ERRC_MOB [MRM] store scell: earfcn[37900] pci[87] rsrp[-438] rsrq[-52] cell_off[0] cell_state[0]

一通call是否成功,通常會去看183以及200ok是否正常

SYS (PCORE) 210267 655146 11:00:49:532 NIL [AT_U p19, s8]+ESIPCPI: 0,1,0,1,0,""
SYS (PCORE) 210790 655724 11:00:49:732 NIL [AT_U p19, s8]+ESIPCPI: 1,0,1,1,183,""
OTA (PCORE) 212078 657976 11:00:49:732 ESM [NW->MS] ESM_MSG_ACTIVATE_DEDICATED_EPS_BEARER_CONTEXT_REQUEST (PTI:0, EBI:7)
OTA (PCORE) 212361 657990 11:00:49:732 ESM [MS->NW] ESM_MSG_ACTIVATE_DEDICATED_EPS_BEARER_CONTEXT_ACCEPT (PTI:0, EBI:7)
SYS (PCORE) 216163 664276 11:00:50:132 NIL [AT_U p19, s8]+ESIPCPI: 1,0,1,1,180,""
SIP 16 745658 11:00:55:412 [NW->MS]CANCEL sip:[2409:8809:8590:4A4A:C376:9C50:8235:1D8A]:50028 SIP/2.0
SYS (PCORE) 229629 745666 11:00:55:412 NIL [AT_U p19, s8]+ESIPCPI: 1,1,0,4,0,""
SYS (PCORE) 229692 745807 11:00:55:412 NIL [AT_U p19, s8]+ESIPCPI: 1,0,1,4,200,""
SYS (PCORE) 229721 745816 11:00:55:412 NIL [AT_U p19, s8]+ESIPCPI: 1,0,1,1,487,""
OTA (PCORE) 231018 746738 11:00:55:412 ESM [NW->MS] ESM_MSG_DEACTIVATE_EPS_BEARER_CONTEXT_REQUEST (PTI:0, EBI:7)
OTA (PCORE) 231067 746742 11:00:55:412 ESM [MS->NW] ESM_MSG_DEACTIVATE_EPS_BEARER_CONTEXT_ACCEPT (PTI:0, EBI:7)

期間主要是通過ECPI這條AT來看這通call，通話過程中的情況，已經掛斷情況

Sim卡流程淺析

Sim card
Step 1：fetch sim record
Line 26574: 09-13 15:50:31.196439 1859 1859 D SIMRecords: [SIMRecords] fetchSimRecords 0 (slot 0)
Line 27143: 09-13 15:50:31.229080 1859 1859 D SIMRecords: [SIMRecords] fetchSimRecords 18 requested: true (slot 0)
Line 27550: 09-13 15:50:31.260930 1859 1859 D SIMRecords: [SIMRecords] fetchSimRecords 0
(slot 1)
Line 28364: 09-13 15:50:31.304495 1859 1859 D SIMRecords: [SIMRecords]fetchSimRecords 18 requested: true (slot 1)
Line 41921: 09-13 15:50:34.155782 1859 1859 D SIMRecords: [SIMRecords] record load complete (slot 0)
Line 48017: 09-13 15:50:37.054278 1859 1859 D SIMRecords: [SIMRecords] record load complete (slot 1)

Step 2：AT command

The information contained in this document can be modified without notice.
12.5 AT+ES3G – Switch 3G Service
12.5.1 Description
This command is used to set the mapping between 3G capability of the protocol and
physical SIM
12.5.2 Format
Command Possible response(s)
+ES3G=[, ]
+CME ERROR:
+ES3G? +ES3G:
+CME ERROR:
12.5.3 Field
: a bit mask value. Each bit corresponding to a physical SIM. This value is
used to indicate that which SIM has the 3G capability. Since we could only support one
SIM to use the 3G capability, only the following values are valid.
1: SIM1
2: SIM2
4: SIM3
8: SIM4
: The network RAT mode after switching. The valid values are as follows.
1: GSM
2: UMTS
3: Dual Mode (GSM and UMTS)
If this value is omitted, the default value is “Dual Mode”

// sim2 set up menu.
04-24 17:52:24.846435 1212 1244 D AT : RIL_URC2_READER Enter processLine:+STKPCI: 0,“D06E810301250082028182050F80005500530049004D53615E9475288F0A01806211768454C1724C8F0A0280670D52A152A974068F0A038065E07EBF57CE5E028F0A048079FB52A87CBE54C18F0A05804E1A52A18D855E028F0A4C805E9475287BA174068F0A4D804E0B8F7D8BBE7F6E”

Sim卡識卡（上報display text）Log位置 radio log

04-21 10:12:03.093014 1049 1081 D AT : RIL_URC2_READER Enter processLine:+STKPCI: 0,“D0308103012101820281028D25085C0A656C76845BA26237FF1A611F8C2260A8900962E94E2D56FD79FB52A8901A4FE1FF01”

Simcard plug out, then plug in.
04-24 17:52:46.985221 1212 1244 D AT : RIL_URC2_READER Enter processLine:+ESIMS: 0,11
04-24 17:53:05.162342 1212 1238 D AT : RIL_URC_READER Enter processLine:+ESIMS: 1,12
04-24 17:53:05.163626 1212 1244 D AT : RIL_URC2_READER Enter processLine:+ESIMS: 1,12

+ESIMS: <sim_inserted_status>,
<sim_inserted_status>: integer
0 SIM not presented
1 SIM presented
: integer
0 SIM_CARD_REMOVED,
1 SIM_ACCESS_ERROR,
2 SIM Refresh
3 // Reserved for other use
MEDIATEK CONFIDENTIAL
4 // Reserved for other use
5 SIM_ACCESS_PROFILE_ON
6 SIM_ACCESS_PROFILE_OFF
7 DUALSIM_DISCONNECTED
8 DUALSIM_CONNECTED
9 SIM_VSIM_ON
10 SIM_VSIM_OFF
11 SIM_PLUG_OUT
12 SIM_PLUG_IN
13 SIM_RECOVERY_START
14 SIM_RECOVERY_END
15 SIM_IMEI_LOCK_FAIL
16 SIM_OP09_LOCK_FAIL

Line 42: 12-21 17:57:11.998423 1410 1410 D SubscriptionController: [getPhoneId] asked for default subId=1 帶卡log

12-20 20:32:20.192271 1407 1432 D SubscriptionController: [getPhoneId]- no sims, returning default phoneId=2147483647, subId1 不帶卡

Modem側Sim中斷

EINT: MD1_SIM2_HOT_PLUG_EINT
MSG_ID_SIM_PLUG_OUT_IND
MSG_ID_SIM_PLUG_IND_IND

一些常用AT
具體詳細內容需要查看MTK的AT_DICUMENT_Modem，以下列舉常用的AT方便便于查看問題

ECSQ 查看信號強度

COPS可以用來查看是什么運營商

CREG，查看駐網情況，是否駐上網，是否帶定位

EAIC 4G call AP發起建立通話
ECPI 4G call通話是附帶的信令如
ECPI: 1,0,0,1,1,20,“13510456281”,129,"tel:13510456281;noa=subscriber;srvattri=national;phone-context=+86為請求升級為視頻通話

AT+CLCC 發起call

AT+CHLD 主動掛斷call，通常可作為是否是用戶主動掛斷的

AT+CDV，電信卡發起call

ETS Id=CP Spy, SpyId=CP IOP ATC recvd data, Data=+CEND:10電信卡掛斷call

rxPwrFilt可以認為是rssi即信號強度

band對應的頻點

GSM:
band900：0～124，975～1023
band1800：512～885
band1900：512～810
band850：128～251

UTRAN TD-SCDMA:
Band A: 10054~10121
Band E: 11504~11996
Band F: 9404~9596

UTRAN FDD:
Band 1: 10562~10838
band 2: 9662 ~ 9938, 412, 437, 462, 487, 512, 537, 562, 587, 612, 637, 662, 687
band 3: 1162 ~ 1513
band 4: 1537 ~ 1738, 1887, 1912, 1937, 1962, 1987, 2012, 2037, 2062, 2087
band 5: 4357 ~ 4458, 1007, 1012, 1032, 1037, 1062, 1087
band 6: 4387 ~ 4413, 1037, 1062
band 7: 2237 ~ 2563, 2587, 2612, 2637, 2662, 2687, 2712, 2737, 2762, 2787, 2812,
2837, 2862, 2887, 2912
band 8: 2937 ~ 3088
band 9: 9237 ~ 9387
band 10: 3112 ~ 3388, 3412, 3437, 3462, 3487, 3512, 3537, 3562, 3587, 3612, 3637,
3662, 3687
band 11: 3712 ~ 3787
band 12: 3842 ~ 3903, 3932, 3957, 3962, 3987, 3992
band 13: 4017 ~ 4043, 4067, 4092
band 14: 4117 ~ 4143, 4167, 4192
band 15: reserved
band 16: reserved
band 17: reserved
band 18: reserved
band 19: 712 ~ 763, 787, 812, 837
band 20: 4512 ~ 4638
band 21: 862 ~ 912
band 22: 4662 ~ 5038

LTE:
0~46589, if not supported, modem will ignore

FDD:
Band 1: 0~599
Band 2: 600~1199
Band 3: 1200~1949
Band 4: 1950~2399
Band 5: 2400~2649
Band 6: 2650~2749
Band 7: 2750~3449
Band 8: 3450~3799
Band 9: 3800~4149
Band10: 4150~4749
Band11: 4750~4949
Band12: 5010~5179
Band13: 5180~5279
Band14: 5280~5379
Band17: 5730~5849
Band18: 5850~5999
Band19: 6000~6149
Band20: 6150~6449
Band21: 6450~6599
Band22: 6600~7399
Band23: 7500~7699
Band24: 7700~8039
Band25: 8040~8699
Band26: 8690~9039
Band27: 9040~9209
Band28: 9210~9659
Band29: 9660~9769
Band30: 9770~9869
Band31: 9870~9919
Band32: 9920~10359

TDD:

Band11: 4750~4949
Band12: 5010~5179
Band13: 5180~5279
Band14: 5280~5379
Band17: 5730~5849
Band18: 5850~5999
Band19: 6000~6149
Band20: 6150~6449
Band21: 6450~6599
Band22: 6600~7399
Band23: 7500~7699
Band24: 7700~8039
Band25: 8040~8699
Band26: 8690~9039
Band27: 9040~9209
Band28: 9210~9659
Band29: 9660~9769
Band30: 9770~9869
Band31: 9870~9919
Band32: 9920~10359
TDD:
Band33: 36000~36199
Band34: 36200~36349
Band35: 36350~36949
Band36: 36950~37549
Band37: 37550~37749
Band38: 37750~38249
Band39: 38250~38649
Band40: 38650~39649
Band41: 39650~41589
Band42: 41590~43589
Band43: 43590~45589
Band44: 45590~46589

總結

以上是生活随笔為你收集整理的MTK modemlog分析的全部?jī)?nèi)容，希望文章能夠幫你解決所遇到的問題。

如果覺得生活随笔網站內容還不錯，歡迎將生活随笔推薦給好友。