平臺
硬件：TQ2440 ?64MB內存 256MB NandFlash bootloader：U-Boot 2015.04 kernel：linux-4.9 Python:?Python-3.6.0 工具鏈：arm-none-linux-gnueabi-gcc ?4.8.3 概述
現在樹莓派很火，在樹莓派上面用戶可以通過Python來控制板子上面的GPIO資源， 然后我想TQ2440也應該做到這一點。 將來根文件系統會通過NFS的方式掛載到開發板上面。 正文
一、工具鏈
登錄這個網址：http://www.veryarm.com/arm-none-linux-gnueabi-gcc
我們這里使用的是最新的Linux解壓版：arm-2014.05-29，由于TQ2440用的arm9屬于armv4t架構，所以在編譯運行于TQ2440上的程序的時候需要給工具鏈傳遞參數-march=armv4t，為了簡單起見，我們可以用下面的辦法：
1 ( pengdl@ubuntu | ~/Study/cross_compile/arm-
2014.05/bin |
Remote:True )
2 $
ls -
l
3 total
22581248
4 lrwxrwxrwx
1 pengdl pengdl
32 Apr
19 19:
53 arm-linux-addr2line -> arm-none-linux-gnueabi-addr2line*
5 lrwxrwxrwx
1 pengdl pengdl
25 Apr
19 19:
54 arm-linux-
ar -> arm-none-linux-gnueabi-
ar*
6 lrwxrwxrwx
1 pengdl pengdl
25 Apr
19 19:
54 arm-linux-as -> arm-none-linux-gnueabi-as*
7 lrwxrwxrwx
1 pengdl pengdl
26 Apr
19 19:
54 arm-linux-c++ -> arm-none-linux-gnueabi-c++*
8 lrwxrwxrwx
1 pengdl pengdl
30 Apr
19 19:
54 arm-linux-c++filt -> arm-none-linux-gnueabi-c++filt*
9 lrwxrwxrwx
1 pengdl pengdl
26 Apr
19 19:
54 arm-linux-
cpp -> arm-none-linux-gnueabi-
cpp*
10 lrwxrwxrwx
1 pengdl pengdl
25 Apr
19 19:
55 arm-linux-cs -> arm-none-linux-gnueabi-cs*
11 lrwxrwxrwx
1 pengdl pengdl
32 Apr
19 19:
55 arm-linux-cs-daemon -> arm-none-linux-gnueabi-cs-daemon*
12 lrwxrwxrwx
1 pengdl pengdl
30 Apr
19 19:
55 arm-linux-elfedit -> arm-none-linux-gnueabi-elfedit*
13 -rwxrwxr-x
1 pengdl pengdl
57 Apr
19 20:
00 arm-linux-g++*
14 -rwxrwxr-x
1 pengdl pengdl
57 Apr
19 20:
06 arm-linux-
gcc*
15 -rwxrwxr-x
1 pengdl pengdl
63 Apr
19 20:
02 arm-linux-
gcc-
4.8.
3*
16 lrwxrwxrwx
1 pengdl pengdl
29 Apr
19 19:
56 arm-linux-
gcc-
ar -> arm-none-linux-gnueabi-
gcc-
ar*
17 lrwxrwxrwx
1 pengdl pengdl
29 Apr
19 19:
56 arm-linux-
gcc-nm -> arm-none-linux-gnueabi-
gcc-nm*
18 lrwxrwxrwx
1 pengdl pengdl
33 Apr
19 19:
57 arm-linux-
gcc-ranlib -> arm-none-linux-gnueabi-
gcc-ranlib*
19 lrwxrwxrwx
1 pengdl pengdl
27 Apr
19 19:
57 arm-linux-gcov -> arm-none-linux-gnueabi-gcov*
20 lrwxrwxrwx
1 pengdl pengdl
26 Apr
19 19:
57 arm-linux-gdb -> arm-none-linux-gnueabi-gdb*
21 lrwxrwxrwx
1 pengdl pengdl
28 Apr
19 19:
57 arm-linux-gprof -> arm-none-linux-gnueabi-gprof*
22 lrwxrwxrwx
1 pengdl pengdl
25 Apr
19 19:
57 arm-linux-
ld -> arm-none-linux-gnueabi-
ld*
23 lrwxrwxrwx
1 pengdl pengdl
25 Apr
19 19:
58 arm-linux-nm -> arm-none-linux-gnueabi-nm*
24 lrwxrwxrwx
1 pengdl pengdl
30 Apr
19 19:
58 arm-linux-objcopy -> arm-none-linux-gnueabi-objcopy*
25 lrwxrwxrwx
1 pengdl pengdl
30 Apr
19 19:
58 arm-linux-objdump -> arm-none-linux-gnueabi-objdump*
26 lrwxrwxrwx
1 pengdl pengdl
29 Apr
19 19:
58 arm-linux-ranlib -> arm-none-linux-gnueabi-ranlib*
27 lrwxrwxrwx
1 pengdl pengdl
30 Apr
19 19:
58 arm-linux-readelf -> arm-none-linux-gnueabi-readelf*
28 lrwxrwxrwx
1 pengdl pengdl
27 Apr
19 19:
58 arm-linux-size -> arm-none-linux-gnueabi-size*
29 lrwxrwxrwx
1 pengdl pengdl
30 Apr
19 19:
58 arm-linux-strings -> arm-none-linux-gnueabi-strings*
30 lrwxrwxrwx
1 pengdl pengdl
28 Apr
19 19:
58 arm-linux-strip -> arm-none-linux-gnueabi-strip*
31 -rwxr-xr-x
1 pengdl pengdl
736300 May
30 2014 arm-none-linux-gnueabi-addr2line*
32 -rwxr-xr-x
2 pengdl pengdl
763504 May
30 2014 arm-none-linux-gnueabi-
ar*
33 -rwxr-xr-x
2 pengdl pengdl
1253360 May
30 2014 arm-none-linux-gnueabi-as*
34 -rwxr-xr-x
2 pengdl pengdl
687056 May
30 2014 arm-none-linux-gnueabi-c++*
35 -rwxr-xr-x
1 pengdl pengdl
734604 May
30 2014 arm-none-linux-gnueabi-c++filt*
36 -rwxr-xr-x
1 pengdl pengdl
686128 May
30 2014 arm-none-linux-gnueabi-
cpp*
37 -rwxr-xr-x
1 pengdl pengdl
186548 May
30 2014 arm-none-linux-gnueabi-cs*
38 -rwxr-xr-x
1 pengdl pengdl
2186780 May
30 2014 arm-none-linux-gnueabi-cs-daemon*
39 -rwxr-xr-x
1 pengdl pengdl
24692 May
30 2014 arm-none-linux-gnueabi-elfedit*
40 -rwxr-xr-x
2 pengdl pengdl
687056 May
30 2014 arm-none-linux-gnueabi-g++*
41 -rwxr-xr-x
2 pengdl pengdl
686128 May
30 2014 arm-none-linux-gnueabi-
gcc*
42 -rwxr-xr-x
2 pengdl pengdl
686128 May
30 2014 arm-none-linux-gnueabi-
gcc-
4.8.
3*
43 -rwxr-xr-x
1 pengdl pengdl
23608 May
30 2014 arm-none-linux-gnueabi-
gcc-
ar*
44 -rwxr-xr-x
1 pengdl pengdl
23576 May
30 2014 arm-none-linux-gnueabi-
gcc-nm*
45 -rwxr-xr-x
1 pengdl pengdl
23576 May
30 2014 arm-none-linux-gnueabi-
gcc-ranlib*
46 -rwxr-xr-x
1 pengdl pengdl
307000 May
30 2014 arm-none-linux-gnueabi-gcov*
47 -rwxr-xr-x
1 pengdl pengdl
4484452 May
30 2014 arm-none-linux-gnueabi-gdb*
48 -rwxr-xr-x
1 pengdl pengdl
805164 May
30 2014 arm-none-linux-gnueabi-gprof*
49 -rwxr-xr-x
2 pengdl pengdl
1200784 May
30 2014 arm-none-linux-gnueabi-
ld*
50 -rwxr-xr-x
2 pengdl pengdl
747500 May
30 2014 arm-none-linux-gnueabi-nm*
51 -rwxr-xr-x
2 pengdl pengdl
912812 May
30 2014 arm-none-linux-gnueabi-objcopy*
52 -rwxr-xr-x
2 pengdl pengdl
1109932 May
30 2014 arm-none-linux-gnueabi-objdump*
53 -rwxr-xr-x
2 pengdl pengdl
763504 May
30 2014 arm-none-linux-gnueabi-ranlib*
54 -rwxr-xr-x
1 pengdl pengdl
420160 May
30 2014 arm-none-linux-gnueabi-readelf*
55 -rwxr-xr-x
1 pengdl pengdl
737260 May
30 2014 arm-none-linux-gnueabi-size*
56 -rwxr-xr-x
1 pengdl pengdl
736332 May
30 2014 arm-none-linux-gnueabi-strings*
57 -rwxr-xr-x
2 pengdl pengdl
912812 May
30 2014 arm-none-linux-gnueabi-strip*
即在原來的工具鏈上面做一些軟連接，對arm-linux-gcc/g++/gcc-4.8.3做一些特殊處理： 1 $
cat arm-linux-
gcc
2 #!/bin/
bash
3 arm-none-linux-gnueabi-
gcc -march=armv4t $*
4
5 $
cat arm-linux-g++
6 #!/bin/
bash
7 arm-none-linux-gnueabi-g++ -march=armv4t $*
8
9 $
cat arm-linux-
gcc-
4.8.
3
10 #!/bin/
bash
11 arm-none-linux-gnueabi-
gcc-
4.8.
3 -march=armv4t $*
此外， 還需要注意的是， 將來在制作用于TQ2440的根文件系統的時候拷貝的工具鏈的lib庫的位置：
arm-
2014.05/arm-none-linux-gnueabi/libc/armv4t/lib
而不是：
arm-
2014.05/arm-none-linux-gnueabi/libc/lib
這個用于高于armv4t架構的平臺，如exynos4412用的是armv7架構。
二、Bootloader
使用的uboot可以到https://github.com/pengdonglin137/u-boot下載，可以參考：
u-boot-2015.04 在tq2440上的移植（使用spl引導u-boot） 將來的分區稍有變化:
| 1MB ?SPL? ?? |
1MB UBOOT? ?? |
1MB PARAMS? ?? |
5MB KERNEL? ?? | 1MB DTB | 247MB ROOTFS |
由于將來采用NFS掛載根文件系統啟動的方式，下面是bootargs以及bootcmd： bootargs：
noinitrd root=/dev/nfs rw nfsroot=
192.168.
1.101:/nfsroot/rootfs ethmac=1C:6F:
65:
34:
51:7E ip=
192.168.
1.6:
192.168.
1.101:
192.168.
1.1:
255.255.
255.0::eth0:off init=/linuxrc console=ttySAC0,115200n
這里板子的IP是192.168.1.6，HOST的IP是192.168.1.101， 當然由于采用了設備樹的方式， 所以也可以不在uboot里設置bootargs，而是放到設備樹的chosen節點當中。
bootcmd： nand read 0x300080000x3000000x500000; nand read 0x320000000x8000000x100000; bootm
0x30008000-
0x32000000 這里會了加快啟動速度， 提前把uImage和dtb文件少些到的nandflash中， 關于在tq2440上面支持dtb，請參考 ?讓TQ2440也用上設備樹（1） 三、kernel
可以到https://github.com/pengdonglin137/linux-4.9下載，tq2440_dt分支， 使用方法參考?讓TQ2440也用上設備樹（1） 燒寫kernel和dtb到nand中：
1 燒寫kernel：
2 mw.b
0x30008000 0xff 0x500000
3 tftp
0x30008000 uImage
4 nand erase
0x300000 0x500000
5 nand
write 0x30008000 0x300000 0x500000
6
7 燒寫dtb：
8 mw.b
0x30008000 0xff 0x100000
9 tftp
0x30008000 dtb
10 nand erase
0x800000 0x100000
11 nand
write 0x30008000 0x800000 0x100000 四、Python
參考?
交叉編譯Python-2.7.13到ARM（aarch32）平臺
交叉編譯Python-2.7.13到ARM（aarch32）—— 支持sqlite3 交叉編譯Python-3.6.0到aarch64/aarch32 —— 支持sqlite3 由于上面兩篇博文采用的是qemu模擬的cortex-a9平臺，屬于armv7架構，而我們的tq2440是armv4架構，所以需要做一些修改。 1 #!/bin/
bash
2
3 ../sqlite-autoconf-
3170000/configure --host=arm-none-linux-
gnueabi \
4 --prefix=`
pwd` \
5 CFLAGS=
"-march=armv4t" \
6 CPPFLAGS=
"-march=armv4t" \
7 LDFLAGS=
"-march=armv4t"
8
9 make -
j4
10 make install 1 #!/bin/
bash
2
3 ../readline-
7.0/configure --host=arm-none-linux-
gnueabi \
4 --prefix=`
pwd` \
5 CFLAGS=
"-march=armv4t" \
6 CPPFLAGS=
"-march=armv4t" \
7 LDFlAGS=
"-march=armv4t"
8
9 make -
j4
10 make install 配置: 1 #!/bin/
bash
2
3 ../termcap-
1.3.
1/configure --host=arm-none-linux-
gnueabi \
4 --prefix=`
pwd`
修改Makefile：
1 CC = arm-none-linux-gnueabi-
gcc
2 AR = arm-none-linux-gnueabi-
ar
3 RANLIB = arm-none-linux-gnueabi-
ranlib
4 ... ...
5 CFLAGS = -g -march=armv4t
然后 make && make install
配置： 1 #!/bin/
bash
2
3 ../Python-
3.6.
0/
configure \
4 --host=arm-
linux \
5 --build=
armv4 \
6 --prefix=`
pwd` \
7 --enable-
ipv6 \
8 --enable-
shared \
9 ac_cv_file__dev_ptmx=
"yes" \
10 ac_cv_file__dev_ptc=
"no" \
11 LDFLAGS=
"-L/home/pengdl/Study/tq2440/Python/SQlite/tq2440/lib \
12 -L/home/pengdl/Study/tq2440/Python/Readline/tq2440/
lib \
13 -L/home/pengdl/Study/tq2440/Python/Termcap/tq2440
" \
14 CPPFLAGS=
"-I/home/pengdl/Study/tq2440/Python/SQlite/tq2440/include \
15 -I/home/pengdl/Study/tq2440/Python/Readline/tq2440/include
" ?別忘了修改Modules/Setup文件，然后執行 make && make install即可。
五、根文件系統
參考博客?用Qemu搭建aarch32學習環境 ? 下面是制作根文件系統的腳本： 1 #!/bin/
bash
2
3 sudo rm -
rf rootfs
4 sudo rm -
rf tmpfs
5 sudo rm -rf ramdisk*
6
7 sudo mkdir rootfs
8 sudo cp ../busybox-
1.24.
2/_install
/* rootfs/ -raf
9
10 sudo mkdir -p rootfs/proc/
11 sudo mkdir -p rootfs/sys/
12 sudo mkdir -p rootfs/tmp/
13 sudo mkdir -p rootfs/root/
14 sudo mkdir -p rootfs/var/
15 sudo mkdir -p rootfs/mnt/
16
17 sudo cp etc rootfs/ -arf
18 sudo mkdir -p rootfs/lib
19
20 sudo cp -arf /home/pengdl/Study/cross_compile/arm-2014.05/arm-none-linux-gnueabi/libc/armv4t/lib/*.so* rootfs/lib
21
22 #Python3
23 sudo mkdir -p rootfs/usr
24 pushd rootfs/usr
25 sudo cp -raf /home/pengdl/Study/tq2440/Python/Python3/tq2440/lib .
26 sudo cp -raf /home/pengdl/Study/tq2440/Python/Python3/tq2440/include .
27 sudo cp -raf /home/pengdl/Study/tq2440/Python/Python3/tq2440/bin .
28 sudo cp -raf /home/pengdl/Study/tq2440/Python/Python3/tq2440/share .
29 sudo arm-none-linux-gnueabi-strip lib/python*
30 popd
31
32 #sqlite3
33 sudo cp -raf /home/pengdl/Study/tq2440/Python/SQlite/tq2440/bin/* rootfs/bin
34 sudo cp -raf /home/pengdl/Study/tq2440/Python/SQlite/tq2440/include/* rootfs/include
35 sudo cp -raf /home/pengdl/Study/tq2440/Python/SQlite/tq2440/lib/* rootfs/lib
36 sudo cp -raf /home/pengdl/Study/tq2440/Python/SQlite/tq2440/share/* rootfs/usr/share
37 sudo arm-linux-strip rootfs/bin/sqlite3
38
39 #readline
40 sudo cp -raf /home/pengdl/Study/tq2440/Python/Readline/tq2440/include/* rootfs/include
41 sudo cp -raf /home/pengdl/Study/tq2440/Python/Readline/tq2440/lib/* rootfs/lib
42
43 sudo rm -f rootfs/lib/libwv* rootfs/lib/libuniconf*
44 sudo rm -f rootfs/lib/*.a
45 sudo rm -f rootfs/lib/*.la
46 sudo arm-none-linux-gnueabi-strip rootfs/lib/*
47
48 sudo mkdir -p rootfs/dev/
49 sudo mknod rootfs/dev/tty1 c 4 1
50 sudo mknod rootfs/dev/tty2 c 4 2
51 sudo mknod rootfs/dev/tty3 c 4 3
52 sudo mknod rootfs/dev/tty4 c 4 4
53 sudo mknod rootfs/dev/console c 5 1
54 sudo mknod rootfs/dev/null c 1 3
55
56 sudo rm /nfsroot/rootfs_bak -rf
57 sudo mv /nfsroot/rootfs /nfsroot/rootfs_bak
58 sudo cp ./rootfs /nfsroot/ -raf 其中的etc目錄可以到這里下載：http://files.cnblogs.com/files/pengdonglin137/etc.zip
六、測試
1 U-Boot
2015.04-g5095150 (Dec
21 2015 -
06:
17:
05)
2 CPUID:
32440001
3 FCLK:
400 MHz
4 HCLK:
100 MHz
5 PCLK:
50 MHz
6 I2C: ready
7 DRAM:
64 MiB
8 WARNING: Caches not enabled
9 Flash:
0 Bytes
10 NAND:
256 MiB
11 In: serial
12 Out: serial
13 Err: serial
14 Net: dm9000
15 Hit any key to stop autoboot:
0
16 NAND read: device
0 offset
0x300000, size
0x500000
17 5242880 bytes read: OK
18 NAND read: device
0 offset
0x800000, size
0x100000
19 1048576 bytes read: OK
20 ## Booting kernel from Legacy Image at
30008000 ...
21 Image Name: Linux-
4.9.
0+
22 Created:
2017-
04-
19 9:
51:
19 UTC
23 Image Type: ARM Linux Kernel Image (uncompressed)
24 Data Size:
3503832 Bytes =
3.3 MiB
25 Load Address:
30008000
26 Entry Point:
30008000
27 Verifying Checksum ... OK
28 ## Flattened Device Tree blob at
32000000
29 Booting using the fdt blob at
0x32000000
30 Loading Kernel Image ... OK
31 Loading Device Tree to 33aa6000, end 33aaa62c ... OK
32 Starting kernel ...
33 Uncompressing Linux...
done, booting the kernel.
34 [
0.000000] Booting Linux on physical CPU
0x0
35 [
0.000000] Linux version
4.9.
0+ (pengdl@ubuntu) (
gcc version
4.8.
3 20140320 (prerelease) (Sourcery CodeBench Lite
2014.05-
29) ) #
1 Wed Apr
19 02:
51:
06 PDT
2017
36 [
0.000000] CPU: ARM920T [
41129200] revision
0 (ARMv4T), cr=
c000717f
37 [
0.000000] CPU: VIVT data cache, VIVT instruction cache
38 [
0.000000] OF: fdt:Machine model: TQ2440
39 [
0.000000] Memory policy: Data cache writeback
40 [
0.000000] DT missing boot CPU MPIDR[
23:
0], fall back to default cpu_logical_map
41 [
0.000000] Built
1 zonelists
in Zone order, mobility grouping on. Total pages:
16256
42 [
0.000000] Kernel command line: noinitrd root=/dev/nfs rw nfsroot=
192.168.
1.101:/nfsroot/rootfs ethmac=1C:6F:
65:
34:
51:7E ip=
192.168.
1.6:
192.168.
1.101:
192.168.
1.1:
255.255.
255.0::eth0:off init=/linuxrc console=
ttySAC0,115200n
43 [
0.000000] PID hash table entries:
256 (order: -
2,
1024 bytes)
44 [
0.000000] Dentry cache hash table entries:
8192 (order:
3,
32768 bytes)
45 [
0.000000] Inode-cache hash table entries:
4096 (order:
2,
16384 bytes)
46 [
0.000000] Memory: 57900K/65536K available (4729K kernel code, 234K rwdata, 1376K rodata, 204K init, 262K bss, 7636K reserved, 0K cma-
reserved)
47 [
0.000000] Virtual kernel memory layout:
48 [
0.000000] vector :
0xffff0000 -
0xffff1000 (
4 kB)
49 [
0.000000] fixmap :
0xffc00000 -
0xfff00000 (
3072 kB)
50 [
0.000000] vmalloc :
0xc4800000 -
0xff800000 (
944 MB)
51 [
0.000000] lowmem :
0xc0000000 -
0xc4000000 (
64 MB)
52 [
0.000000] modules :
0xbf000000 -
0xc0000000 (
16 MB)
53 [
0.000000] .text :
0xc0008000 -
0xc04a67f0 (
4730 kB)
54 [
0.000000] .init :
0xc0627000 -
0xc065a000 (
204 kB)
55 [
0.000000] .data :
0xc065a000 -
0xc0694840 (
235 kB)
56 [
0.000000] .bss :
0xc0694840 -
0xc06d60a8 (
263 kB)
57 [
0.000000] SLUB: HWalign=
32, Order=
0-
3, MinObjects=
0, CPUs=
1, Nodes=
1
58 [
0.000000] NR_IRQS:
103
59 [
0.000000] irq: clearing pending status
00000002
60 [
0.000000] _get_rate: could not
find clock xti
61 [
0.000131] sched_clock:
16 bits at 1000kHz, resolution 1000ns, wraps every 32767500ns
62 [
0.000254] clocksource: samsung_clocksource_timer: mask:
0xffff max_cycles:
0xffff, max_idle_ns:
29163075 ns
63 [
0.001154] Console: colour dummy device 8
0x30
64 [
0.001358] Calibrating delay loop...
199.47 BogoMIPS (lpj=
498688)
65 [
0.035124] pid_max: default:
32768 minimum:
301
66 [
0.035715] Mount-cache hash table entries:
1024 (order:
0,
4096 bytes)
67 [
0.035803] Mountpoint-cache hash table entries:
1024 (order:
0,
4096 bytes)
68 [
0.039125] CPU: Testing
write buffer coherency: ok
69 [
0.041720] Setting up static identity map
for 0x30008200 -
0x30008258
70 [
0.067396] clocksource: jiffies: mask:
0xffffffff max_cycles:
0xffffffff, max_idle_ns:
9556302231375000 ns
71 [
0.068020] pinctrl core: initialized pinctrl subsystem
72 [
0.071279] NET: Registered protocol family
16
73 [
0.074528] DMA: preallocated
256 KiB pool
for atomic coherent allocations
74 [
0.096698] cpuidle: using governor ladder
75 [
0.097401] No ATAGs?
76 [
0.357763] SCSI subsystem initialized
77 [
0.359225] usbcore: registered new interface driver usbfs
78 [
0.359894] usbcore: registered new interface driver hub
79 [
0.360865] usbcore: registered new device driver usb
80 [
0.364272] Advanced Linux Sound Architecture Driver Initialized.
81 [
0.395750] clocksource: Switched to clocksource samsung_clocksource_timer
82 [
0.462505] NET: Registered protocol family
2
83 [
0.466700] TCP established hash table entries:
1024 (order:
0,
4096 bytes)
84 [
0.466838] TCP bind hash table entries:
1024 (order:
0,
4096 bytes)
85 [
0.466899] TCP: Hash tables configured (established
1024 bind
1024)
86 [
0.467514] UDP hash table entries:
256 (order:
0,
4096 bytes)
87 [
0.467638] UDP-Lite hash table entries:
256 (order:
0,
4096 bytes)
88 [
0.468746] NET: Registered protocol family
1
89 [
0.547937] RPC: Registered named UNIX socket transport module.
90 [
0.548047] RPC: Registered udp transport module.
91 [
0.548062] RPC: Registered tcp transport module.
92 [
0.548076] RPC: Registered tcp NFSv4.
1 backchannel transport module.
93 [
0.556526] futex hash table entries:
256 (order: -
1,
3072 bytes)
94 [
0.565590] workingset: timestamp_bits=
30 max_order=
14 bucket_order=
0
95 [
0.699034] NFS: Registering the id_resolver key type
96 [
0.699281] Key type id_resolver registered
97 [
0.699297] Key type id_legacy registered
98 [
0.699372] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
99 [
0.699649] jffs2: version
2.2. (NAND) ?
2001-
2006 Red Hat, Inc.
100 [
0.709262] romfs: ROMFS MTD (C)
2007 Red Hat, Inc.
101 [
0.730545] io scheduler noop registered
102 [
0.730657] io scheduler deadline registered
103 [
0.732323] io scheduler cfq registered (default)
104 [
0.947381]
50000000.serial: ttySAC0 at MMIO
0x50000000 (irq =
32, base_baud =
0) is a S3C2440
105 [
1.387359] random: fast init
done
106 [
1.611283] console [ttySAC0] enabled
107 [
1.767633] brd: module loaded
108 [
1.772241] s3c24xx-nand 4e000000.nand: Tacls=
1, 10ns Twrph0=
3 30ns, Twrph1=
1 10ns
109 [
1.774282] s3c24xx-
nand 4e000000.nand: NAND ECC disabled
110 [
1.780114] nand: device found, Manufacturer ID:
0xec, Chip ID:
0xda
111 [
1.786112] nand: Samsung NAND 256MiB
3,3V
8-
bit
112 [
1.790528] nand:
256 MiB, SLC, erase size:
128 KiB, page size:
2048, OOB size:
64
113 [
1.798195] nand: NAND_ECC_NONE selected by board driver. This is not recommended!
114 [
1.805811] Scanning device
for bad blocks
115 [
1.835095] Bad eraseblock
364 at
0x000002d80000
116 [
1.835485] Bad eraseblock
369 at
0x000002e20000
117 [
1.848196] Bad eraseblock
558 at
0x0000045c0000
118 [
1.884281] Bad eraseblock
1291 at
0x00000a160000
119 [
1.909046] Bad eraseblock
1792 at
0x00000e000000
120 [
1.909215] Bad eraseblock
1793 at
0x00000e020000
121 [
1.925484] Creating
6 MTD partitions on
"tq2440-0":
122 [
1.925650]
0x000000000000-
0x000000100000 :
"SPL"
123 [
1.934143] ftl_cs: FTL header not found.
124 [
1.941575]
0x000000100000-
0x000000200000 :
"U-BOOT"
125 [
1.949569] ftl_cs: FTL header not found.
126 [
1.954926]
0x000000200000-
0x000000300000 :
"PARAMS"
127 [
1.963831] ftl_cs: FTL header not found.
128 [
1.969370]
0x000000300000-
0x000000600000 :
"KERNEL"
129 [
1.978445] ftl_cs: FTL header not found.
130 [
1.984058]
0x000000600000-
0x000000700000 :
"DTB"
131 [
1.993049] ftl_cs: FTL header not found.
132 [
1.998630]
0x000000700000-
0x000010000000 :
"ROOTFS"
133 [
2.010883] ftl_cs: FTL header not found.
134 [
2.023036] eth0: dm9000e at c4932000,c4934004 IRQ
7 MAC:
00:
00:de:ad:be:ef (platform data)
135 [
2.026768] ohci_hcd: USB
1.1 'Open' Host Controller (OHCI) Driver
136 [
2.032382] ohci-
s3c2410: OHCI S3C2410 driver
137 [
2.039610] s3c2410-ohci
49000000.usb_ohci: OHCI Host Controller
138 [
2.042708] s3c2410-ohci
49000000.usb_ohci: new USB bus registered, assigned bus number
1
139 [
2.051552] s3c2410-ohci
49000000.usb_ohci: irq
26, io mem
0x49000000
140 [
2.124944] hub
1-
0:
1.0: USB hub found
141 [
2.127292] hub
1-
0:
1.0:
2 ports detected
142 [
2.133433] usbcore: registered new interface driver usb-
storage
143 [
2.136449] mousedev: PS/
2 mouse device common
for all mice
144 [
2.141909] s3c-rtc
57000000.rtc: rtc disabled, re-
enabling
145 [
2.145961] rtc rtc0: alarm rollover not handled
146 [
2.149532] rtc rtc0: invalid alarm value:
1900-
2-
1 0:
0:
0
147 [
2.156227] s3c-rtc
57000000.rtc: rtc core: registered s3c as rtc0
148 [
2.162236] i2c /
dev entries driver
149 [
2.168574] s3c2410-wdt
53000000.watchdog: watchdog inactive, reset disabled, irq disabled
150 [
2.175323] sdhci: Secure Digital Host Controller Interface driver
151 [
2.178802] sdhci: Copyright(c) Pierre Ossman
152 [
2.185919] hidraw: raw HID events driver (C) Jiri Kosina
153 [
2.197719] usbcore: registered new interface driver usbhid
154 [
2.197849] usbhid: USB HID core driver
155 [
2.206738] NET: Registered protocol family
17
156 [
2.207505] Key type dns_resolver registered
157 [
2.272831] s3c-rtc
57000000.rtc: setting system clock to
2000-
04-
11 20:
01:
10 UTC (
955483270)
158 [
2.305173] dm9000
20000000.ethernet eth0: link down
159 [
4.410138] dm9000
20000000.ethernet eth0: link up, 100Mbps, full-duplex, lpa
0xCDE1
160 [
4.412435] IP-
Config: Complete:
161 [
4.415784] device=eth0, hwaddr=
00:
00:de:ad:be:ef, ipaddr=
192.168.
1.6, mask=
255.255.
255.0, gw=
192.168.
1.1
162 [
4.425577] host=
192.168.
1.6, domain=, nis-domain=
(none)
163 [
4.431373] bootserver=
192.168.
1.101, rootserver=
192.168.
1.101, rootpath=
164 [
4.439728] ALSA device list:
165 [
4.441430] No soundcards found.
166 [
4.489327] VFS: Mounted root (nfs filesystem) on device
0:
12.
167 [
4.491287] Freeing unused kernel memory: 204K (c0627000 -
c065a000)
168 [
4.496048] This architecture does not have kernel memory protection.
169 Please press Enter to activate this console.
170 [root@tq2440 ]#
171 [root@tq2440 ]#
172 [root@tq2440 ]#
ls
173 bin etc lib mnt root sys usr
174 dev include linuxrc proc sbin tmp var
1 [root@tq2440 ]# python3
2 Python
3.6.
0 (default, Apr
19 2017,
20:
20:
18)
3 [GCC
4.8.
3 20140320 (prerelease)] on linux
4 Type
"help",
"copyright",
"credits" or
"license" for more information.
5 >>> print(
"Hello World")
6 Hello World
7 >>>
import sqlite3
8 >>>
1 [root@tq2440 ]# python3 /usr/lib/python3.
6/test/
test___all__.py
2 __phello__.foo
3 _bootlocale
4 _collections_abc
5 _compat_pickle
6 _compression
7 _dummy_thread
8 _markupbase
9 _osx_support
10 ... ...
11 .
12 ----------------------------------------------------------------------
13 Ran
1 test
in 97.391s
14 OK
?
完
總結
以上是生活随笔為你收集整理的移植Python3到TQ2440（一）的全部內容，希望文章能夠幫你解決所遇到的問題。
如果覺得生活随笔網站內容還不錯，歡迎將生活随笔推薦給好友。
